Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to professional auto locksmiths with the right equipment and know-how. They can create and program keys faster and less expensive than a dealership.
If your key fob stopped locking or unlocking your doors, it could be due to a dead coin battery. There are also other reasons why the key may be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also making it impossible to start the engine. If this is the case, you'll need to make use of the backup starting procedure that is detailed in your vehicle's owner manual.
Another reason your 208 might not start is because the spark plugs are worn down. The spark plugs ignite the fuel to start the engine. However they have a finite time of life. They'll eventually fail in the event that they aren't utilized enough.
There is a straightforward solution to this problem. The best solution is to determine the voltage of your car battery with a multimeter. If the voltage is below 11,5 volts, it's the time to replace it. It is also important to clean the contacts of the battery when it has corrosion. You can do this by lifting the rubber covers that cover the two terminals on the battery and using wire brushes to clean any corroded areas of the battery. Then, you should connect the cables for the positive and negative poles.
Water Damage
If your 208 will not start and the battery has not gone flat, you should check the spark plugs. It could be that they're dirty and do not spark. The spark plugs can be cleaned in a workshop.
Peugeot cars are equipped with a key with a transponder compatible with the immobiliser. This guarantees that only the right key is able to turn the engine. If the chip inside the Peugeot key is damaged then it will not transmit the proper signal to the vehicle.
This is a typical issue that is caused by water damage. This is a common issue in areas with colder temperatures where the vehicle has been exposed to rain or snow. In this instance, you should contact a reputable locksmith who will have the tools and equipment required to reprogram the key. They also have the latest technological know-how and machinery required to make the Peugeot 208 smart key. The process should not take more than 15 minutes.
Faulty Battery Contacts
Peugeot replaced the transponder chips by introducing a new model that utilizes electronic components mounted on a circuit board. The new system is effective when it's new, but over time the circuit boards begin to wear out and stop functioning correctly.
This can prevent the immobiliser chip from working, so your car won't start. If www.thekeylab.co.uk is the case it's a good idea contact a Peugeot specialist or locksmith.
Another issue that is common is when the key fob battery starts to die, this causes the key blade to stop from entering the lock. A car locksmith will replace the battery, and then cut a new key blade for you. This is a simple fix.
Faulty Receiver Module
If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden downpour or accidentally washing it or washing it, it could be due to a defective receiver module. The receiver is responsible for sending radio frequency signals to an on-board computer, which controls the central locking system in your Peugeot vehicle.
The key fob itself has rubber seals that prevent water from getting to the chip inside. However prolonged exposure to water may penetrate these seals and damage the chip. Submerging the key fob into the ocean at the beach or throwing it into the pool could be particularly damaging due to the high salt content.
The module will have to be replaced if your Peugeot spare key isn't working anymore. This is only done by a skilled auto locksmith or Peugeot specialist. Peugeot keys, unlike other cars, are secured by an immobilizer system. This requires the correct programming to allow the car to start. This is the reason that you should only rely on the Peugeot locksmith to create and program an alternative.
Computer malfunctioning on-board
The computer on board in your Peugeot is responsible for a variety of the systems inside your vehicle, from airbags to power windows. If something is wrong with these systems, it'll typically display a code that identifies the problem. The code is stored in the system until the problem is fixed. Most often, this involves replacing the computer on board.
One of the most common causes of the light coming on is loose or corroded connectors in the airbag sensor. This can be caused by wear and tear, aging, or exposure to salt and moisture. It is crucial to get this issue addressed as quickly as possible, since an airbag that is malfunctioning can be dangerous in the event an accident.
If you encounter an error message that says "card not found" on your Peugeot key fob, the battery inside the key fob might be dead or weak. This will stop the key fob from sending a signal that will disable the immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your car. If this doesn't work, then the key battery is in need of replacement.